Stand-Off or Insert Nuts for Stromberg Carlson Ladder Rack

Question

Question:

2014 Thor Windsport motorhome. Need to purchase ladder stand off nut for this rv. Any help appreciated.

asked by: Patricia B

0

Expert Reply:

We have replacement stand-off or insert nuts for RV ladders but none that are made specifically for a motor home as each piece of hardware used on motor homes is not available in a data base.

If by chance you have an aftermarket ladder, the Stromberg Carlson RV Exterior Ladder # LA-401 or # LA-401BA then we do have the Replacement Stand-Off or Insert Nut for Stromberg Carlson RV Ladder # FST-9975. This also works with their Bunk Ladders # LA-460 and # LA-466.

This replacement nut is about 1" diameter and 1" tall.

expert reply by: Kyle S

0

Answer 1

The base on the Replacement Stand-Off Brace for the Surco Universal Exterior RV Ladders #SPN-416 slides over the standoff tube and is held back with the lip formed by the end of the tube because the tube is widened at the other end. The base is…

view full answer...

Answer 2

I went out into our warehouse and measured the Replacement Stand-Off Brace #SPN-416 and found that it measures 5-1/2 inches. This is the only standoff tube we offer at this time.

view full answer...

Answer 3

The Replacement Stand-Off Brace for Surco Universal Exterior RV Ladders #SPN-416 measures 5 inches in length and has a diameter of 1 inch.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 7

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the…

view full answer...

Answer 8

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...

Answer 9

The side plates on the 3" Wide Continuous Hinge #MA65VR you found are 0.09" thick which is just under 3/32". We do have a 3" Wide #MA52VR which is 6' Long with a 1/2" pin that has 0.18"…

view full answer...

Answer 10

I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures 40-1/2" long x 29"…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 12

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have…

view full answer...

Stand-Off or Insert Nuts for Stromberg Carlson Ladder Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching