Recommended Wheel/Tire Combo and Fenders for Aluminum Boat Trailer

Question

Question:

My trailer for my aluminum boat currently has 8inch wheels and I really want to upgrade to bigger wheels and to do that I think I need new fenders as well. I need help figuring out what will work for me. Thanks!

asked by: Rob

0

Expert Reply:

For your wheel size upgrade, I recommend the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel - 5 on 4-1/2 - Load Range C # AM3H400 or the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel - 4 on 4 - Load Range C # AM3H380 depending on your hub bolt pattern. I've attached an article to assist in determining that and I recommend the galvanized wheel because it is a boat trailer and these wheels will hold up to the water or salt water without corrosion.

For your fenders if you need to replace them based on tire size, I recommend the Single Axle Trailer Fender w Top Step - Style B - Black Plastic - 8" to 12" Wheels - Qty 1 # F008559. We also have aluminum fenders # HP49VR if you prefer. I've attached a link to all your options. You can use the Mounting Brackets for Trailer Fender - 8"/12" Wheels - Galvanized Steel - Qty 2 # CE26061G-2 to mount them.

expert reply by: Jason S

0

Answer 1

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 2

It looks like all 2015 Honda Pilots come equipped with a hitch already (save for a select few). It's for that reason that none of our manufacturers made hitches for it, and why the 2016 hitches will not fit. In the middle of your back bumper, you…

view full answer...

Answer 3

All of the 2015 Honda Pilots would have a hitch installed on them from Honda. So that is one less piece of the puzzle that you would need. Since you wanted to do some towing you might be interested in etrailer ball mount kit #989900. It comes with 2…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The Curt Adjustable Width Trailer Hitch Receiver for RVs #13703 uses frame brackets for installation, and those need to be positioned on the inside of an I-beam frame, as per the instructions (a copy of which I have linked for you). That is what will…

view full answer...

Answer 6

There are 2 different capacities independent of each other though related. Tongue weight is the downward force or weight on the trailer hitch. So it is pushing down at the back of the vehicle. The gross trailer weight is the weight of whatever it is…

view full answer...

Answer 7

There is not a fuse we carry for the 8000 Series of Fan-Tastic vent. It does use a 4 amp slow blow fuse so to make fuse access simpler you can use In-Line Fuse Holder #C58470-1 and if you need to replace the bow-tie bracket, motor, and blade the…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 10

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Recommended Wheel/Tire Combo and Fenders for Aluminum Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching