Does Draw Tite Hitch # 75673 Fit on 2018 Subaru Outback Wagon

Question

Question:

I inquired about the 2018 Subaru Outback Class 3 trailer hitch. Since the 2018 arent out yet, are these actually 2017 but fit a 2018? Do you also have a list of companies that will be able to install this in my area? Martinez, CA. Thank you. This is my 2nd hitch purchase from you.

asked by: Jan

0

Expert Reply:

The Draw Tite Hitch part # 75673 is a carry over from the 2017 Subaru Outback to the 2018 model. Draw Tite was able to get their hands on this vehicle very early to test fit and confirm the fit. I attached an installed picture for you to check out as well.

Hitch installs are very basic for mechanics compared to some of the more difficult jobs they can get. What we recommend is finding a local mechanic in your area that has a good reputation and go with them.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the etrailer Trailer Hitch Receiver part #e98847 which is a fit for a 2014 Subaru Outback Wagon does indeed fit models with dual exhaust.

view full answer...

Answer 2

The Outback Sport is referring to the Subaru Impreza model that is called the Outback Sport. The Draw-Tite Class III 2 Inch Hitch, part #75673, is visible underneath the rear fascia, but the receiver tube does not protrude from under the vehicle.…

view full answer...

Answer 3

The Draw-Tite part #75673 that you referenced has been confirmed as a fit for your 2015 Subaru Outback and has a 600 lb tongue weight rating so IT has enough capacity for towing your trailer, but if the vehicle ends up having a lower tongue weight…

view full answer...

Answer 4

It looks like Subaru only offers a class I, 1-1/4" trailer hitch for a 2011 Subaru Outback. Therefore, if you need a class III, 2" trailer hitch for your 2011 Subaru Outback you will have to use an aftermarket trailer hitch. The issue with…

view full answer...

Answer 5

When we installed Draw-Tite 2-Inch hitch #75673 on a 2017 Subaru Outback Wagon we measured the height of the top of the receiver opening as 15-inches above ground. You can see this dimension illustrated in the linked video at the 1:40-minute mark.…

view full answer...

Answer 6

For your 2010 Subaru Outback Wagon 3.6R with dual exhaust we have the Draw Tite hitch part #75673 which we know is a fit. We've had a few customers with the 3.6R model that has dual exhaust like yours come back and state that they were able to…

view full answer...

Answer 7

view full answer...

Answer 8

The only thing that needs to be removed and trimmed is the heat shield or heat shields when installing #75673. We have other hitches #76227 that will mount to the same mounts that the bumper beam is. The difference is that you will not have to trim…

view full answer...

Answer 9

The Draw-Tite Max-Frame Trailer hitch part #76227 requires removing the foam bumper support temporarily for installation. The video does show the installer cutting the plastic fascia and then replacing the foam bumper support that comes with the…

view full answer...

Answer 10

If you are careful installing the Draw Tite hitch part #76227 you shouldn't have any issue with the trim pieces damaging but if you do the only place to get them is a Subaru dealer.

view full answer...

Answer 11

Draw-Tite 2-inch hitch #76227 is a confirmed fit on the 2019 Subaru Outback Wagon and for your reference I linked both the written instructions and an installation video showing a 2019 model year. Hardware is not included with the hitch since it uses…

view full answer...

Answer 12

In regards to a 2016 Subaru Outback Wagon, you have two options which are ones that mount behind the bumper like the Draw-Tite Max-Frame Trailer Hitch Receiver part #76227 and ones that mount under the bumper like the Draw-Tite Max-Frame Trailer…

view full answer...

Does Draw Tite Hitch # 75673 Fit on 2018 Subaru Outback Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching