Weight Difference Between Equalizer Weight Distribution Systems for 600 lb & 1,000 lb Tongue Weight

Question

Question:

what is the actual product weight difference between the 1000 and the 600?

asked by: Warren B

0

Expert Reply:

The Equalizer part # EQ37100ET with a 1,000 lb max tongue weight weighs 109 lbs.

The part # EQ37060ET for 600 lbs tongue weight weighs 98 lbs so the difference is 11 lbs.

expert reply by: Jameson C

0

Answer 1

I am not sure what you mean by too much spring action. If you are wanting to downgrade the system by using lower rated spring bars, you would do so because the current bars are NOT providing enough spring. In any event, my Equal-i-zer representative…

view full answer...

Answer 2

The Equal-i-zer Weight Distribution System part #EQ37060ET only comes with a 2" hitch ball but we do offer the 2-5/16" hitch ball separately as the 2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems part #EQ91-00-6100. If…

view full answer...

Answer 3

Whether or not you need a weight distribution hitch for you Lance 1475 depends on several things. 1. Is the trailer weight more than 50 percent of your vehicle's weight? 2. Is the rear of your tow vehicle sagging when the trailer is hooked up? 3.…

view full answer...

Answer 4

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your 2007…

view full answer...

Answer 5

The Curt MV Weight Distribution System w/ Friction Sway Control - Round Bar - 14K GTW, 1.4K TW #C17063 is far too large a system for your trailer tongue weight and that may be part of the sway issue as that will make your trailer too rigid in its…

view full answer...

Answer 6

Yes, the Equal-I-zer Weight Distribution System #EQ37060ET fits a 2 inch trailer hitch receiver that is rated for use with a weight distribution system. The weight distribution system comes with a 2 inch diameter hitch ball as well. This system has a…

view full answer...

Answer 7

The Equal-i-zer weight distribution spring bars and heads are both designed to fit specific tongue weight ratings so you'd have to replace both. So to uprate your system to 1,000 lbs tongue weight you'd need the head part #EQ90-02-1000 and…

view full answer...

Answer 8

The Equal-i-zer Weight Distribution System part #EQ37060ET (90-00-0600) is rated for a total tongue weight of 200 lbs - 600 lbs whereas the Equal-i-zer Weight Distribution System part #EQ37100ET (90-00-1000) is rated for a total tongue weight of 600…

view full answer...

Answer 9

If the vehicle is pulling after you have installed the Roadmaster Steering Stabilizer part #RM-RBK24-RSSC then loosen the bracket U-bolts at the tie rod and re position it. Tighten the bolts and test drive it once again, repeating the process until…

view full answer...

Answer 10

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 11

The issue is definitely that you have an underrated system, which is why you are experiencing sway. The Equal-i-zer Weight Distribution System #EQ37060ET you said you have now is rated for total tongue weights - the tongue weight of your fully loaded…

view full answer...

Answer 12

For a single 800 pound Fastway weight distribution spring bar you will need #FA94-02-0899. This is for round bar systems. If you have a trunnion bar system then the 800 pound bar is #FA92-02-0899. If you were to use the 1,000 pound capacity bars it…

view full answer...