Replacement Hardware For Curt TruTrack Weight Distribution System

Question

Question:

Do you sell the keeper retainer clip and cotter pin for the Curt 17501 TRUTRACK TM TRUNNION BAR WEIGHT DISTRIBUTION SYSTEM?

asked by: Kent R

0

Expert Reply:

For your Curt TruTrack weight distribution system, the Curt Coupler Safety Pin 1/4" # K-8P and the Replacement L-Pins and Clips for Curt TruTrack Weight Distribution System w/ Sway Control - Qty 2 # C17513 are confirmed fits. If you need more replacement hardware, you may be interested in # C17554

expert reply by: Jason S

0

Answer 1

I have some good news to offset some of that anger from recently being scammed. We do indeed have all of the replacement parts available for the Curt TruTrack Weight Distribution System #C17500 and I will list them out below. Replacement L-Pins and…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Robin, Yes, you can absolutely use the 2" Equal-i-zer Weight Distribution Shank #EQ90-02-4600 with the Blue Ox SwayPro Weight Distribution #BXW2000. The hole spacing on the Equal-i-zer shank is the same as the Blue Ox shank which is why they…

view full answer...

Answer 6

The Dexter 8-133 axle according to my contact at Dexter is an old motorhome axle they no longer make. Their tech said the motorhome axles like what you have are designed for one time use so there are not compatible parts made for even replacement…

view full answer...

Answer 7

The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 45 Amp #PD4045KA is the replacement we have for your unit. It is larger because it also is the panel and is 12-1/4" long x 8-3/4" tall x 7-1/4" deep…

view full answer...

Answer 8

Unlike passenger car tires that have a certain range the tire needs to be inflated to, trailer tires should always be kept inflated to the maximum air pressure listed on the sidewall of the tire. We offer the Kenda Karrier 145/80-12 (aka 145/R12) in…

view full answer...

Answer 9

Actually all you really have to do is remove the oil from the hub and then pack the hubs with grease and then get the correct bearing buddy to match the threaded hub bore. You will need to measure the inner diameter of where the old grease cap…

view full answer...

Answer 10

The CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies part #CE10196G-4 can be used on a 4" frame with the CE Smith U-Bolt part #CE15254A.

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

The best replacement size option we offer for a 185R14C 8PR is the Castle Rock ST205/75R14 Radial Trailer Tire part #LHCK201. This new tire will be just slightly larger in diameter and width so there should be no issues. It has a 75 mph speed…

view full answer...