Recommended Mounting Plate to Mount 9K Badland Winch Onto Car Trailer

Question

Question:

What would you recommend what type of mounting plate to put on a car trailer for a 9000 lb Badland winch

asked by: Richard L

0

Expert Reply:

I recommend using the Bulldog Winch Universal Mounting Plate for Truck and Trailer Winches # BDW20291 for your Badland Winch, which has a 4-Bolt mounting pattern (center on center) of 10" x 4-1/2".

For hardware you will want to use the Bulldog Winch Hardware for Universal Mounting Plate for Truck Winches # BDW20297.

expert reply by: Jon G

0

Answer 1

Here are the steps to prepare your 2023 Ford Bronco Big Bend for flat towing. The transfer case and transmission will be in neutral with the ignition off. This information is in your owners manual. Switching Neutral Tow On 1.Switch your vehicle to…

view full answer...

Answer 2

Hi Francis; after a lot of checking with our manufacturers I found out there is not a base plate/tow bar that will work with your Bronco Everglades edition with the winch.

view full answer...

Answer 3

The best SumoSprings for your 2023 Ford Bronco depends on what you are using them for - just to improve your ride a bit on rougher roads, or to help with sag when you are towing or maybe using an accessory. I'll go ahead and list out the options…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to install the Redarc Tow-Pro Elite Brake Controller part #RED63RR on a 2022 Ford Bronco you'll first need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #22292 which will make for a plug and play install up at…

view full answer...

Answer 6

The closest compatible option for your Dometic DOTR12CB RV microwave's size is the Furrion Standard RV Microwave #FMSN09BL. It measures 19-1/16" W x 13-5/8" H x 15-7/8" D with a 0.9 cu ft capacity.

view full answer...

Answer 7

If your trailer has separate turn signals from the brake lights and you want them to remain that way, you will need to use a special converter. On the trailer side, behind the 7-Way, you will attach the Vehicle to Vehicle Taillight Converter,…

view full answer...

Answer 8

I agree, the bag for the NOCO Boost X Jump Starter #NOC88VR is a nice way to keep everything together but it definitely lacks in the protective department. To keep your Boost X Jump Starter safer you'll want to pick up the EVA Protection Case…

view full answer...

Answer 9

The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part #34823 will be the correct replacement.

view full answer...

Answer 10

You will need to lock out the sliding function on your Pull Right 5th wheel hitch to use the Ram Gooseneck to 5th Wheel Trailer Coupler Adapter item #KPG5-R30IP. If you can not lock out your slider than I recommend the Curt Spyder Gooseneck Trailer…

view full answer...

Answer 11

Yes, the Demco Spare Tire Carrier part #DM15851-76 does work great with the tire size ST235/80R16 that you referenced. We had a customer with your exact tire size send us a picture of it carrying the wheel which I attached.

view full answer...

Answer 12

Yes, the Warn M8000 Winch uses a 10" x 4-1/2" mounting pattern which the Curt Trailer Hitch Electric Winch Mount Plate part #C31010 will accept so they can be used together just fine. The 10" x 4-1/2" mounting pattern is an…

view full answer...