Replacing A 125255UC Double Lip Grease Seal

Question

Question:

Trailer grease seals. Hub is on a torsion axle from Northern Tool. Existing double lip seals have number 125255CU. OD is 1.975 OD of spindle is 1.230 width is .390. Pls advise.

asked by: Lee B

0

Expert Reply:

The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part # 34823 will be the correct replacement.

expert reply by: Jesse M

0

Derek

5/2/2024

Are you absolutely sure about that inner diameter measurement? Every other listing I look at shows the ID for seal code 125255UC at 1.25" or 1.249"

Reply

Jesse M.

5/3/2024

@Derek Looks like we had some bad/dated info on our site that recommended the wrong seal size. After a bit of digging we got to the bottom of it. The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part # 34823 will be the correct replacement. Sorry for any confusion. The answer above will be updated.

Reply

Answer 1

The locking storage box #M387FR mounts in the floor. As long as you have the 19" wide x 29" long x 7-1/4" deep space, it can absolutely work in a toyhauler. The box recesses into the floor and is powder coated for protection against…

view full answer...

Answer 2

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 3

Your Kendon fold-up trailer has a 2K axle, given the 1.063 diameter spindle you referenced. Assuming you have idler hubs, you'd need #8-91-05UC1-EZ for a 4 on 4 bolt pattern or #AKIHUB-545-2-LF-2K for a 5 on 4-1/2 inch bolt pattern. The L44649…

view full answer...

Answer 4

The Yates Wobble Roller #YR440R will leave black marks but you can use the yellow version #YR500YW-6P instead to avoid marking up your boat. I confirmed this with my contact at Yates. This has a slightly larger diameter at 5" as opposed to the…

view full answer...

Answer 5

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 6

Hey Dave, what you gave me is enough info to get you replacement bearings. The grease seal 471750 matches the part #TMK48ZR. For a Timken replacement for the L44610 part number you'd need #TMK63VR. Then for a bearing for the L44649 you'd want…

view full answer...

Answer 7

The key for selecting a replacement grease seal is the reference number, in this case #10-9. The manufacturer code does not matter. This is a single-lip seal with an inner diameter of 1.500-inches and an outer diameter of 1.987-inches. It is…

view full answer...

Answer 8

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 9

Hey Cory, thanks for reaching out! The Replacement Support Leg #TH33VK is for the 8-1/2" long Thule HideAway awnings which is what I believe will be a better match than the part #TH48VK you referenced, which is for a 10' long HideAway…

view full answer...

Answer 10

So from what I can gather, the E3 error code on your Furrion Electric RV Fireplace with Logs #F30SW15ABL is an "overheat protection" error which explains why it only runs for a bit before shutting off. I'd recommend inspecting the…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Replacing A 125255UC Double Lip Grease Seal

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching