Installation And Torque On Roadmaster Reflex Steering Stabilizer

Question

Question:

On the instruction sheet, I do not see an reference except in the video that says to tighten the chassic bracket bolts to factory specs. I have not way of know what factory specs on these bolts are? This is on a 2017 Forest River FR3 30 DS with Xpkg. with 190 WB, GVW 18000 Also do you need to put red loctite on these bolts?

asked by: BURTON G

0

Expert Reply:

For your Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK22-RSSA, you should have received instructions. My apologies if this wasn't the case. I've attached a photo of the torque requirements from the instructions and have also attached the instruction link.

I recommend using the Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube # LT37420 because they will be vibrating and you don't want the bolts to come loose.

expert reply by: Jason S

0

click to enlarge

Answer 1

I pulled a Jensen LED RV Smart TV #ASA98VR from the warehouse and hooked up in our office to test it out and found that the only apps you can download are the ones in the "Smart TV Apps" app, which isn't much. I then called the…

view full answer...

Answer 2

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 3

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 4

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 5

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Answer 8

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...

Answer 9

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 10

To flat tow your 2021 Jeep Wrangler Unlimited 4Xe Rubicon Hybrid you will need a tow bar, base plate, tow bar wiring kit, braking system, and safety cables. I have the following recommendations for you listed below: Tow Bar: Roadmaster Nighthawk All…

view full answer...

Answer 11

To replace/upgrade the bushings on the rear factory sway bar of your 2009 Class A Newmar Canyon Star RV you need one of the following Roadmaster kits based on the diameter of your factory sway bar: - 1-3/8" Diameter #RM-4139-300 - 1-1/2"…

view full answer...

Answer 12

The Roadmaster #RM-1139-140 and #RM-1139-148 are both replacement anti-sway bars for a Ford F550 or F53 Class A motorhome chassis. Both bars are 1-3/4 inches in diameter. The #RM-1139-140 fits models with a GVWR of 22K-24K, and the #RM-1139-148 fits…

view full answer...