Correct 2009 Class A Newmar Canyon Star RV Rear Sway Bar Bushing Replacement Kit

Question

Question:

I have a 2009 Class A Newmar Canyon Star RV mounted on a 2008 Ford F-53 chassis. I am trying to order replacement sway bar bushings for the rear sway bar. Can you tell me the correct model number for these bushings?

asked by: James L

0

Expert Reply:

To replace/upgrade the bushings on the rear factory sway bar of your 2009 Class A Newmar Canyon Star RV you need one of the following Roadmaster kits based on the diameter of your factory sway bar:

- 1-3/8" Diameter # RM-4139-300
- 1-1/2" Diameter # RM-4139-125

These are going to be a nice upgrade to what you currently have.

expert reply by: Jon G

0

Answer 1

Some of the bushings on the Roadmaster #RM-4139-125 will need to be pressed in, but it is not overly difficult. I included an install video we have of a similar Roadmaster kit that will show how this needs to be done.

view full answer...

Answer 2

I recommend having your suspension checked out to make sure there are no issues, but if everything is fine, suspension enhancement springs would help level your Itasca. I could not guarantee this will "fix" your lean but the…

view full answer...

Answer 3

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 4

For a first-time base plate installer we estimate that the total time required to mount the Blue Ox Base Plate Kit #BX2261 to be a good 5 to 6 hours (half a day, let's call it). Our installers who have the benefit of having done this many…

view full answer...

Answer 5

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 6

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 7

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 10

We do have that exact lube with the Aqua Lube part #RM-400-011-30.

view full answer...

Answer 11

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 12

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Correct 2009 Class A Newmar Canyon Star RV Rear Sway Bar Bushing Replacement Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching