Does Lippert Components Power Stabilizer Trailer Jack Item # LC298707 Come as a Single or Pair

Question

Question:

Is this product a zset of two jacks or individual jacks

asked by: Randy

0

Expert Reply:

Lippert Components Power Stabilizer Trailer Jack Item # LC298707 is a single jack that spans the width of the trailer frame and will have a leg on the left and right sides. We actually have a few different electric stabilizers like this and I have included a link to them for you. They are all sold as individual units (except the Ground Control system which is completely different than the others).

expert reply by: Michael H

0

Answer 1

Yes, the Lippert Components Power Stabilizer Jack #LC298707 that you referenced is what you will want to replace your jack with the part number 369777 (as pictured) with. My contact at Lippert Components verified this.

view full answer...

Answer 2

It sounds like you have got a good start on the troubleshooting. The next step would be to check the motor. I recommend using an alternate source to power the motor. If the motor still isn't working then it will need to be replaced. In order to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 8

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 11

I attached a picture that shows the install instructions for the Lippert Components High-Speed Power Stabilizer Jack #LC298707 that you referenced and in it you'll notice a set distance isn't specified for where it has to install on the…

view full answer...

Answer 12

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Does Lippert Components Power Stabilizer Trailer Jack Item # LC298707 Come as a Single or Pair

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching