Install Instructions for Lippert Components High-Speed Power Stabilizer Jack # LC298707

Question

Question:

Hi How far back from the rear of the trailer do you need to mount the LCI power stabilizing jack LC298707?

asked by: Tom

1

Helpful Expert Reply:

I attached a picture that shows the install instructions for the Lippert Components High-Speed Power Stabilizer Jack # LC298707 that you referenced and in it you'll notice a set distance isn't specified for where it has to install on the frame.

I also attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 2

The Lippert Components High-Speed Power Stabilizer Jack - 30" Lift #LC298707 does have a manual override mode in case the motors or battery have an issue. You will use a 5/16 inch socket if that is ever needed and I've attached the…

view full answer...

Answer 3

The Replacement 6-Amp Auto Reset Breaker for Lippert Components Power Stabilizer Jack #LC134181 are designed for use with the Lippert Electric Stabilizer Jacks that have switches such as the Lippert Components High-Speed Power Stabilizer Jack -…

view full answer...

Answer 4

Yes, for the LaSalle Bristol Single Bowl RV Bathroom Sink, #34416305PWA, I suggest the LaSalle Bristol Pop Up Drain for RV Bathroom Sinks - 1-1/2" threaded diameter, #34465WPR1303.

view full answer...

Answer 5

We have an easy solution for your Lippert jack to give it the additional 4 inches of extension you are wanting with the Fastway Flip Automatic Fold-Up Jack Foot #FA88-00-4500. This is the correct size for the jack inner tube diameter of your jack…

view full answer...

Answer 6

I spoke with Furrion and was able to track down the part number 2021123933 for the charcoal filter that goes in the top of the Furrion Over the Range RV Convection Microwave #FMCM15SS. This part is something that you'll have to actually call…

view full answer...

Answer 7

The 20 amp fuse you are looking for on the #LC298707 is a fuse holder like what you can see in the attached diagram.

view full answer...

Answer 8

Yes, the arms of the Roadmaster Falcon 2 Tow Bar #RM-520 will extend and lock into position when you start pulling your vehicle. The bars can often be difficult to release when you go to disconnect the tow bars from the towed vehicle when you get…

view full answer...

Answer 9

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 10

Yes, the Lippert Electric Stabilizer Jack 113407 can be replaced with the Lippert High-Speed Power Stabilizer Jack part #LC298707. It will be a direct bolt-on swap, just simply cut and reattach the new wires and you'll be ready for use.

view full answer...

Answer 11

The powered stabilizer jack set you'd need to replace the 198641 is the part #LC298707 as the number you have now has been discontinued but the #LC298707 is basically the current version of what you already have so it will fit and work great…

view full answer...

Answer 12

You do not necessarily need to add the Lippert Components Double Spacer for RV Electric Stabilizer Jack #LC266030 to your new Lippert Components High-Speed Power Stabilizer Jack #LC298707. If you install your new stabilizer and find you need the…

view full answer...

Install Instructions for Lippert Components High-Speed Power Stabilizer Jack # LC298707

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching