Replacement Steel Fender for 1994 Procraft Single Axle Boat Trailer

Question

Question:

Looking for the exact fender to fit my 1994 trailer which is metal and bent up pretty bad any thoughts?

asked by: Chris

0

Expert Reply:

Your trailer appears to have steel fenders and we do offer these as well as tough ABS plastic types and aluminum fenders too. You can see all replacement trailer fenders on the linked page.

Just click on your trailer's wheel diameter and your preferred material to narrow down the products displayed. We do not carry exact trailer-specific replacement fenders but between all the types and sizes we carry you should be able to find a suitable part.

For example, for a steel fender with backing plate to fit 14- or 15-inch wheels use part # HP36VR. Mounting brackets are also linked for your reference.

expert reply by: Adam R

0

click to enlarge

Answer 1

I went out to the warehouse and measured the internal width of Square Trailer U-Bolts #SP01-160. They are 2-1/8 inches wide on the inside. They are designed for a 2 inch square axle using 1-3/4 inch to 2 inch wide springs.

view full answer...

Answer 2

Unfortunately no, the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #PXQT550CH4 is only available in chrome. We do have the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #PXQT545BHS which is identical but it only works with a 5 on 4 1/2…

view full answer...

Answer 3

For your Karavan trailer I recommend LED tail lights #STL57RB and #STL56RB. They are a little shorter at 6-1/16 inches but they do mount on studs spaced 2 inches apart on center. they are 3-5/8 inches tall and 2-1/4 inches deep overall. I have linked…

view full answer...

Answer 4

In order to replace the Advent Analog Wall Thermostat ACTH11 you'll need the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners part #ACRG15. This is a digital style replacement which is what you'll need since…

view full answer...

Answer 5

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 8

Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for…

view full answer...

Answer 9

The Fulton Single Axle Trailer Fender with Top Step #F008554 is designed to fit tire on a 14 inch wheel. The dimensions are: 9.7" wide x 31.3" long x 12.75" tall. The top step is 8 inches wide and it has a capacity of 300 lbs. You can…

view full answer...

Answer 10

There is no way to find an exact replacement. The replacement fenders we carry are built as universal items that you would fit based on tire size. I would replace both of the fenders when you buy the boat so that they will match. We have both plastic…

view full answer...

Answer 11

Yes the brackets #CE10002G-4 would easily support the weight of your 2,060 lb boat.

view full answer...

Answer 12

I spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, like part #CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of…

view full answer...