Tandem Axle Lift Kit for 3,500 Pound Torflex Axles

Question

Question:

Im looking to purchase K71-725-02 for my Trail-lite Trailcruiser fifth wheel trailer TC-524RK. Im wondering 1 is it the right part current axles are Lippert lc135-tb. Id like to raise the axles at least 3.

asked by: Ryan

0

Expert Reply:

Your axle is a 3,500 pound axle so the lift kit you need is # K71-707-02. This is for axles rated between 2,300 to 4,000 pounds. It'll give you a lift of 2-5/8 inches.

The # K71-725-02 kit is for 5,500 to 7,000 pound axles.

expert reply by: Charles S

0

Answer 1

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 2

We have 3-1/8 inch lift kits for the Torflex axles like part #K71-725-02 but we do not have any 4 inch kits at this time.

view full answer...

Answer 3

Manufacturers don't keep detailed records of the specific parts that are on year, make and model of trailers, and since those parts could have changed over the years the only way to know if the Torflex Lift Kit #K71-725-02 will work for you is if…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Tandem Axle Lift Kit for 3,500 Pound Torflex Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching