Mounting Hole Pattern Dimensions for Control Module of Titan Brake Rite

Question

Question:

Hello, Can you please provide the hole mounting pattern for the control module. The 4 hole and the 2 hole patterns please. Thanks,

asked by: Ivon L

1

Helpful Expert Reply:

I went out into our warehouse to get the mounting pattern dimensions of the module of the Brake Rite part # T4813102.

From left to right they are all 6-3/4 inches apart.

From the top holes to the bottom holes they measure 2-3/8 inches apart.

From the top holes to the middle holes measures 1-1/4 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Check out the picture I attached that shows the electrical connections that the Titan BrakeRite #T4813100 will make. I also attached installation instructions for this product for you to check out. The updated version of the Titan BrakRite is the…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

I recommend replacing an entire ladder if it's damaged. You'll want to find a replacement based on the height. Such as the Stromberg Carlson #LA-401 that is 99-1/2 inches tall. They can be cut shorter to customize the length if needed.

view full answer...

Answer 12

For your 4x6 utility trailer, I recommend using the Taskmaster 4.80R12 Radial Trailer Tire part #TT48012C. This tire has a radial ply construction which will be better for the longer highway trips you intended to make. It has a load range C rating…

view full answer...

Mounting Hole Pattern Dimensions for Control Module of Titan Brake Rite

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching