Replacement Hardware Kit for Curt TruTrack Weight Distribution Hitch C17500

Question

Question:

Hello, over the weekend i purchased a curt 17500 hitch at a fleamarket. after opening the somewhat destroyed box i noticed i was missing some parts based on parts list. from the parts list i am missing 6,7,8,9,and 10. i am assuming they were all in one bag of parts. the bolts and nuts i am sure i could get through a hardware store locally but number 6 head tilt spacers i doubt i will find. do you offer the head tilt spacers 2 of them separately or can you get them for me if so how much?

asked by: Brian

0

Expert Reply:

My contact at Curt confirmed you can use their Replacement Hardware Kit # C17550 to replace the missing components in your TruTrack weight distribution hitch # C17500. The kit includes the following

(2) Wire-lock linchpins
(2) Head tilt washers
(1) 3/4-10 x 5" Hex bolt
(1) 3/4-10 x 4" Hex bolt
(2) 3/4"-10 Nylock nuts
(1) 5/8" Hitch pin with clip

expert reply by: Adam R

0

Answer 1

Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW Item #C17500 uses standard bolt sizes, not metric. The 3/4" bolts that hold the head to the shank get torqued to 200 foot pounds each. The nuts…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 5

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 12

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Replacement Hardware Kit for Curt TruTrack Weight Distribution Hitch C17500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching