Landing Pads For Rails Of A Carry On Utility Trailer For Yakima Control Towers

Question

Question:

I need a set of Yakima Landing Pads for my Yakima Control Towers that will fit the side rails of a Carry On utility trailer. I was thinking a 1 or 4. Any advice would be appreciated.

asked by: Tom P

0

Expert Reply:

If the rails you are referring to on your utility trailer are the track style, then your Yakima Control Towers will fit with Landing Pad 4 for Yakima Control Towers - Qty 2 # Y00224. If you will me drilling into metal support rails then you will want the Landing Pad 7 for Yakima Control Towers for Metal Roofs - Qty 2 # Y00227.

You may also be interested in the Round 78" CrossBars for Yakima Roof Rack System (QTY 2) # Y00411 or the Round 86" CrossBars for Yakima Roof-Rack System (QTY 2) # Y00420 to fit your trailer.

If you need replacement control towers, I recommend the Replacement Yakima Control Tower for Factory-installed Tracks (QTY 1) # Y8890027.

expert reply by: Jason S

0

Answer 1

The difference between Landing Pad 1 #Y00221 and Landing Pad 4 #Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 5

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 8

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 9

Thanks for the picture! Yes, it will. The old factory connector on your 2005 GMC Yukon XL Denali will pop out once you disconnect the wiring harness and you'll be able to insert the Curt Replacement OEM USCAR Trailer Connector item #C42JR.

view full answer...

Answer 10

No, I am sorry we do not! To remove the Titan Chain Snow Tire Chains item #TC1555 you will disconnect the tensioning chain with red clips and the green hook, both on the outside of the tire and then the straight pin connector on the inside-facing…

view full answer...

Answer 11

To remove and install the Left Raised Rail Foot #1500052316 from your AeroBlade Edge roof rack all you have to do is remove the torx head screw from the main assembly and the rail foot will slide right off. Attached is a close-up photo of an…

view full answer...

Answer 12

The 4-way install harness part #C56020 that you referenced is a confirmed fit for your 2005 Ford E-150 van and would be one component needed to install your Curt Echo part #C79DR. You would also need the part #C26DR with 10 gauge wire part #10-1-1…

view full answer...