What Landing Gear is On Cougar Fifth Wheel

Question

Question:

I need to know what Landons gear is used on my 5 wheel .my 5wheel weight 11000 # it is electric with one motor. I know there are several different weight class.

asked by: Don O

0

Expert Reply:

From previous customers with your trailer we have determined that your trailer has Lippert landing gear like the part # LC333964 which fits also the description you listed.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 9

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Answer 10

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 11

Your typical electric jack is designed to fit an A-frame so the only one we carry that is a side mount is the Fulton XLT #F141401. However, you may be interested in the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV64FR. This jack has a hand…

view full answer...

Answer 12

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...