Brophy Camper Tie Downs that Fit 2013 Ram 2500HD

Question

Question:

Will these tie down work for my 2013 Dodge Ram? 2500 HD crew cab, full box.

asked by: Al M

0

Expert Reply:

The Brophy Angled Hold-Downs # HSAB, Camper Hold Down # HSSF, and the Camper Hold Down Zinc Finish # HSBP will all fit your 2013 Ram 2500.

The Brophy Angled Hold-Downs # HSAB have neoprene pads to protect your truck's paint. They also provide more clearance between the hold-downs and the outside truck fenders.

If you need hardware to tie down your camper, I recommend the Camper Tie-Down Hardware Package # TDHP.

expert reply by: Jameson C

0

Answer 1

I checked with Torklift and the correct camper tie downs for your truck are the #TLD2119 for the front and for the rear #TLD3109.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The trim kit included with the High Pointe Standard RV Microwave #HP39ZR is 20.75” W x 15” H.

view full answer...

Answer 10

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

Hey Chip, so we do have a set of Torklift camper tie downs that fit your 2024 Ford F-350 long bed with side steps and a factory hitch with the part number #TL87CR for the front set and part #TLF3008 for the rear set.

view full answer...

Brophy Camper Tie Downs that Fit 2013 Ram 2500HD

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching