Location Recommendation for Switches of Ultra Fab Powered Stabilizer Jack

Question

Question:

WHERE WOULD YOU RECOMEND LOCATING OF UP AND DOWN SWITCHES AND DO THE MOTORS STOP AUTOMATICALLY WHEN YOU PUT THEM UP OR WILL I JUST KEEP GOING UNTIL YOU BLOW A FUSE? HOW DO I KNOW WHEN THEY ARE UP ALL THE WAY IN THE HOME POSITION ?

asked by: JAMES C

0

Expert Reply:

Typically the switches of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941705 that you referenced gets mounted to the trailer frame. UF prefers if you can mount them in a storage bin or somewhere else that's at least slightly weatherproof and child proof.

You'll want to keep an eye on the legs of the jack as you raise and lower them and release the switch when the legs are all the way up. The motor will continue to run if you raise the jacks all the way up but you wouldn't need to be too afraid of blowing the fuse if you were to let it run a second too long. Just don't sit there laying on the switch if the jacks are up already and you'll be fine.

expert reply by: Jameson C

0

Answer 1

The Ultra-Fab Stabilizer #UF39-941705, though technically not designed to lift the trailer, per se, will still provide some lift when leveling the trailer out. That being said, these are rated to 6,000 pounds of leveling lift, but as a general rule,…

view full answer...

Answer 2

Since you are at 22 inches it would not hurt to go with the taller model #UF39-941705 especially since you never know the type of terrain you might be in. I have included a link to a video review of this jack for you.

view full answer...

Answer 3

There's guide out there to tell me exactly what stabilizer you have on your Fleetwood Wilderness GLX so I would need to know the exact system before I could give you the correct steps. Typically there will be a manual override spot on the head of…

view full answer...

Answer 4

I can tell you how to wire the motors of the Ultra-Fab Power Twin II Electric Stabilizer #UF39-941705, but the manufacturer doesn't provide a diagram, just the written instructions, which are pretty simple to follow. You'll need to wire the…

view full answer...

Answer 5

The Ultra-Fab Power Twin II Electric Stabilizer, part #UF39-941705 features dual motors and is capable of lifting up to 6,000 lbs with either side. You said you are parked on a very uneven site. My contact at Ultra-Fab said that this system can lift…

view full answer...

Answer 6

Technically yes but you would only have 6,000 at the front and 6,000 at the rear using 2 sets of the Power Twin stabilizer, #UF39-941705. Often the back of the trailer is heavier so you would have to make sure that the weight at either point does not…

view full answer...

Answer 7

The Ultra Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced is designed for exactly what you are looking for so it would work well as long as your frame dimensions are compatible with it. If your trailer frame…

view full answer...

Answer 8

The Ultra Fab kit part #UF39-941705 would be a great option. This attaches to the bottom of the frame of your camper and allows you to independently control to jack legs on either side of the trailer to level and stabilize it. I attached a review…

view full answer...

Answer 9

Typically stabilizer jacks and leveling jacks are the same thing. The Ultra Fab part #UF39-941705 can do both as well. It can lift up to 30 inches from where the jacks are mounted on the trailer. When the jacks are at their max height they have a…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Location Recommendation for Switches of Ultra Fab Powered Stabilizer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching