Recommended Rear Timbren Spring Clearance On A Lifted 2014 Chevrolet Silverado

Question

Question:

I put timbrens on the rear of my 2014 chevy half ton. The truck has a one inch lift in the rear. Should I add one inch spacers to the timbrens? I have about one and a half inch gap between the timbrens and the truck axel now. Thanks

asked by: Peter G

0

Expert Reply:

Per the manufacturer's recommendations, there should be approximately 1"-1.5" of clearance between the rear contact point and the Timbren Rear Suspension Enhancement part # TGMRCK15S when not under load. Too little space will cause the spring to constantly ride on the axle/bracket resulting in a bouncy uncomfortable ride where as, a spring to far from the contact point will not allow for the full capabilities of the spring to be exerted.

Since you currently have 1"-1.5" of clearance, I would not add a 1" spacer to the rear of your Timbrens. Doing so will not allow enough space between the spring and rear contact point of your vehicle.

I have attached a photo of the Timbren Springs installed on a 2013 Chevrolet 1500 for reference.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Timbren Rear Suspension Enhancement System part #TGMRCK15S which is a fit for a 2014 Chevrolet Silverado 1500 comes with both replacement jounce springs so you will only need to order one kit. The Timbrens are going to be an excellent option to…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 4

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 5

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 6

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 7

Since the Trimax #TMX56RR did not fit, I recommend taking a look at the etrailer 5th Wheel King Pin Lock #e98896. I like this lock because it is designed to be universal, and will fit virtually any pin box with a standard kingpin. The collar of the…

view full answer...

Answer 8

Hi there David; we do have truck camper jacks that can work for your F-250 with a lift and large tires. What you can use are camper jacks from Brophy, which have a 17" to 67" lift range, which is the highest possible lift height. There are…

view full answer...

Answer 9

The Trimax King Pin Lock #TMX56RR can still be used with your 5th wheel having a capture plate from PullRite. The capture plate mounts to the top of the kingpin and only takes up a similar amount of space that a Lube Plate #RP83002 would. If you…

view full answer...

Answer 10

You are going to need the Replacement Rails #PE54AJ for the Pace Edwards Switchblade Metal Retractable Hard Tonneau Cover #311-SMC3250 on your 2017 Chevrolet Silverado 1500. The Rails #311-SW5128 you found are for the Cover #311-SMFA05A28 which fits…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...