Replacement Landing Gear For 2009 Keystone Everest

Question

Question:

I have a 2009 keystone everst its a heavy trailer. ...I need a new set of lifting legs..

asked by: Sterling K

0

Expert Reply:

The Landing Gear Kit part # RVLG-8000 is a fit for your 2009 Keystone Everest. This kit is designed to fit trailers with weld stops that are 17-1/2 inches apart from each other measured on the outsides of the stops. From speaking with a previous customer we have found that your trailer is a match for this kit's mounting dimensions.

This kit has a lifting capacity of 8k which would work well for your trailer.

I attached a picture that shows this.

expert reply by: Jameson C

0

Answer 1

There could be a few reason as to why the landing gear legs on your 2012 Jayco Eagle M-351 RLTS are not working correctly. There could be a power shortage, faulty motor, or damaged internals. The easiest one to check is if the trailer's battery…

view full answer...

Answer 2

I believe you are asking about the weld stops on the Replacement Heavy Duty Landing Gear Master Leg #LC241846. As shown in the attached diagram, the distance from the top of the upper weld stop to the bottom of the lower one on #LC241846 is 17.5…

view full answer...

Answer 3

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 4

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 7

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 8

In order to pick out a direct replacement for the landing gear on your 2001 sunnybrook 31bwfs we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 11

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Answer 12

It sounds like you're saying it is hooked up to power but it doesn't have the ability to raise the trailer. This could be the batteries or a problem with the wiring. It is probably getting power, it just may not be enough to lift the trailer.…

view full answer...