How to Pick Out Replacement Landing Gear for 1985 Prowler to Replace RBW Legs
Question:
I have Rbw legs both nuts stripped off worm gear..as you know RBW is no longer a thing, Id like to know if by chance you know what model landing gear Id need to replace the legs Being that I have em apart and cant find replacement parts... its a 1985 propeller 245k, 24-25.
asked by: Nate S
Expert Reply:
In order to pick out a direct replacement for the landing gear on your 2007 Desert Fox 38U we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the # BD500162.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Bolt-On
- 2 Jacks
- Bulldog
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Curt TriFlex NEXT Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Suspension Enhancement
- Shop: Tailgate
- Shop: Brake Controller
- Shop: Autowbrake Electric Brake Controller - Trailer Mount w/ Remote Fob - 1 to 3 Axles - Proportional
- Video: Lippert SolidStep RV Steps Installation - 2021 Grand Design Transcend Xplor Travel Trailer
- Q&A: Troubleshooting Vehicle Battery Drain After 7-Way and Brake Controller Installation
- Shop: Lippert SolidStep RV Steps for 25" to 28-7/8" Wide Doorways - 3 Steps
- Shop: Progressive Dynamics 4000 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel - 60 Amp
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear - 33-1/2" Long
- Search Results: 44649
- Q&A: How to Read the Lippert Components Axle Description Measurements
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Review of CURT Trailer Brake Controller - Proportional Controller - C24VV
- Search Results: 68149
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Article: Brake Controller Installation: Starting from Scratch
- Search Results: 25580
- Q&A: Replacement for Demco Master Cylinder 05680-C for Drum Brakes
- Search Results: trailer brake controller
- Video: Curt TriFlex NEXT Trailer Brake Controller Installation - 2021 Jeep Cherokee
- Q&A: Parts Needed to Install Brake Controller on 2012 Chrysler Town and Country
- Article: Towing a Trailer? Let's Talk About Brake Controllers