Distance Bracket Sticks Out on Brophy Scissor Steps

Question

Question:

How far does the mounting bracket stick out from the bumper? I would like a set of 5steps to mount to the back of a enduramax gladiator toyhauler. There is a lift gate on the back and want to make sure it will clear the bracket when being raised and lowered

asked by: Cheryl V

0

Expert Reply:

On the Brophy Scissor Steps # AS04 there is about 7 to 7-1/2 inches when the steps are at their highest point from the bracket to the closest edge of the top step.

The mounting bracket itself does not stick out at all.

expert reply by: Charles S

0

Answer 1

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points…

view full answer...

Answer 2

The mounting bracket of the #AS04 is 25 inches wide. The step width is 18 inches.

view full answer...

Answer 3

We have a couple of 4-step scissor stairs you could use. We have a steel model, #SS04, and an aluminum model, #AS04, and both are 18 inches wide. These stairs mount using an included bracket that looks like #AS2002. So they do not pin into place.…

view full answer...

Answer 4

The bracket of the Aluminum Scissor Steps #AS04 that you referenced stays attached to the camper, but the steps themselves get removed while traveling. Check out the review video I attached for these steps as well.

view full answer...

Answer 5

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps! For…

view full answer...

Answer 6

The scissor step bracket has two L shaped pins on the inside of the angle iron. Measure the center to center distance between the two pins. You will want to drill two 7/16 inch holes into the tailgate that are the same distance apart as the pins that…

view full answer...

Answer 7

What you're going to want instead is the: -Brophy Tailgate Scissor Step Mounting Bracket #TSSB. This mounting bracket will work with your AS04 scissor steps, as well as the AS02, AS03, AS05, AS23, AS24, AS25, SS02, SS03, and SS04 steps. The…

view full answer...

Answer 8

I've attached some dimensions below to help you determine fitment of the Brophy Camper Scissor Steps #AS24 with your truck bed camper. The mounting bracket is 24" long x 1" tall (1-3/8" tall if you include the V-Clamps) so…

view full answer...

Answer 9

I really like the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide - 375 lbs #TLA7804-8000 and think they're a great option for your truck bed camper and the bracket has pull pins to allow you to remove the steps…

view full answer...

Answer 10

The SolidStep Manual Fold-Down Steps #LC678027 have a top step which is 13" deep and the other steps are 8-1/2" deep so you would need at least that much depth from your bumper to the top step. These particular steps may not be the best…

view full answer...

Answer 11

Yes. The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375 lbs - Black Bracket #TLA7834 can be removed from the bracket by detaching the pull pins like the #TLA7804-8000. The main issue you might have is that the bracket…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...