Brophy Aluminum Camper Scissor Bracket Width

Question

Question:

I have a Northstar pop-up camper with no steps. Height to camper floor is 33. Im wondering what the width of the mounting bracket is on a Brophy Camp Scissor Step 4 steps.

asked by: Kevin B

0

Expert Reply:

The mounting bracket of the # AS04 is 25 inches wide.

The step width is 18 inches.

expert reply by: Jameson C

0

Answer 1

We have a couple of 4-step scissor stairs you could use. We have a steel model, #SS04, and an aluminum model, #AS04, and both are 18 inches wide. These stairs mount using an included bracket that looks like #AS2002. So they do not pin into place.…

view full answer...

Answer 2

On the Brophy Scissor Steps #AS04 there is about 7 to 7-1/2 inches when the steps are at their highest point from the bracket to the closest edge of the top step. The mounting bracket itself does not stick out at all.

view full answer...

Answer 3

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for…

view full answer...

Answer 4

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps!…

view full answer...

Answer 5

I've attached some dimensions below to help you determine fitment of the Brophy Camper Scissor Steps #AS24 with your truck bed camper. The mounting bracket is 24" long x 1" tall (1-3/8" tall if you include the…

view full answer...

Answer 6

The bracket of the Aluminum Scissor Steps #AS04 that you referenced stays attached to the camper, but the steps themselves get removed while traveling. Check out the review video I attached for these steps as well.

view full answer...

Answer 7

The scissor step bracket has two L shaped pins on the inside of the angle iron. Measure the center to center distance between the two pins. You will want to drill two 7/16 inch holes into the tailgate that are the same distance apart as the pins that…

view full answer...

Answer 8

What you're going to want instead is the: -Brophy Tailgate Scissor Step Mounting Bracket #TSSB. This mounting bracket will work with your AS04 scissor steps, as well as the AS02, AS03, AS05, AS23, AS24, AS25, SS02, SS03, and SS04 steps. The…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.

view full answer...

Brophy Aluminum Camper Scissor Bracket Width

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching