Will Reese Round Spring Bars Fit a Pro Series Weight Distribution Head

Question

Question:

will the PRO series round distribution head receive Reese round bars ? The Reese replacement head has an upper and lower hole/opening into which the round bar end fits , but with the PRO series head having a contained receiver with grease zerks I cant tell if the upper hole/opening is shaped to receive a Reese type round bar.....??

asked by: Charles C

0

Expert Reply:

Only the RB2 head, # 58333, is the same between certain Reese systems and Pro Series systems so head # PS58442 will not work with the Reese round spring bars. If you can tell me the part number of the Reese system you have I can look up which head fits it.

expert reply by: Michael H

0

Answer 1

I went ahead and confirmed with my contact at Curt that the spring bars on the Curt TruTrack 2P Weight Distribution System w/ Sway Control - 7-Hole Shank #C69JR are 35" from end to end. I went ahead and attached a diagram of this measurement for…

view full answer...

Answer 2

You have the Pro Series weight distribution head part #58333 which means the correct replacement spring bars you need are the part number #58338 which has a tongue weight range of 600-1,200 which which would work great with a trailer that weighs…

view full answer...

Answer 3

Based on what you described we have two options that should be what you need. If you have a trunnion (square bar) setup the head you would need is the part #RP58167. Or if the spring bars are round the part #RP58112 would be what you need.

view full answer...

Answer 4

The weight distribution heads will always have a 1-1/4 inch hole for the ball shank. Therefore, the replacement round bar head, part #RP58112, will accommodate a hitch ball with a 1-1/4 inch shank.

view full answer...

Answer 5

It looks like you have parts of two different systems. One is parts is the dual cam arm of the Strait-Line Weight Distribution System w Sway Control - Round Bar #RP66087 and the other is a Draw-Tite Pro Series #PS58442. I recommend the Replacement…

view full answer...

Answer 6

The sway control ball on the Replacement Weight Distribution Bolt-Together Round Bar Head #PS58442 can be used with two balls and you can use the balls on either side of the head assembly (see picture). This replacement head fits Pro Series weight…

view full answer...

Answer 7

The Replacement Head for Reese Weight Distribution System - Round Bar #RP58112 will work with all Reese round bars that insert and twist for installation. I've attached a photo to assist. As long as the top of your round bars look like #PS58440,…

view full answer...

Answer 8

By hitch I assume you mean the shank. I would need to know the model number of the weight distribution system to get you the correct replacement arms. If you could get back to me with that information I may be able to find a solution for you.

view full answer...

Answer 9

The correct replacement head you would need for your Reese 12k round bar weight distribution system you have is the part #RP58112 and not the part #58333 that you referenced.

view full answer...

Answer 10

It looks like you've got an obsolete Pro Series 10k Weight Distribution System. The Replacement Weight Distribution Bolt-Together Round Bar Head part #PS58442 is the correct replacement. However, it appears you're also missing a weight…

view full answer...

Answer 11

The Replacement Head for Reese Weight Distribution System #RP58112 will work as a replacement head for your 1,200 lb round bar system. The S1 or S2 stamped on the side of the head doesn't make a difference.

view full answer...

Answer 12

For the Pro Series RB2 system and its head, #58333, there are different spring bars you could use. You need to go by the total tongue weight of the set up. This is the tongue weight of the trailer when loaded and ready to tow plus the weight of…

view full answer...

Will Reese Round Spring Bars Fit a Pro Series Weight Distribution Head

Product Page this Question was Asked From

Continue Researching