Replacement Hitch Pin Options for Swagman Bike Rack

Question

Question:

Hi, I lost the bolt that attaches the rack to the car hitch. It doesnt seem to be any of the sizes of bolts that I can find at a hardware store. Can I order a new bolt from the company? Or, can you tell me the thread TPI of a bolt that will work? It seems to be a 7/16inch or similar metric size. Thanks,

asked by: David M

0

Expert Reply:

I believe you are looking for a replacement hitch pin bolt for a Swagman bike rack. For that we have the part # P5901 for just the pin/bolt or if you wanted to upgrade to a locking hitch pin we have the # S64029.

expert reply by: Jameson C

0

Answer 1

I want to make sure I get you the correct information but I cannot find any information on a Swagman SR-8190-02 bike rack. The Threaded Hitch Pin and Clip #P5901 is proprietary size used on Swagman bike racks with a threaded 2" hollow tube…

view full answer...

Answer 2

The usable length of the Replacement Threaded Hitch Pin and Clip #P5901 is roughly 3-1/4". I recommend measuring this on your 2-1/2" receiver to verify fitment as not all receivers will have the same dimensions. We do have the longer…

view full answer...

Answer 3

The Swagman Traveler XC2 Bike Rack for 2 Bikes - 2" Hitches or RV Bumpers #S64663 is designed to work with the 2" receiver on your truck as well as the included RV bumper mount receiver so you should have no problems using the threaded…

view full answer...

Answer 4

If you leave the hitch lock for the Swagman Dispatch 2 Bike Platform Rack part #S44FR on for too long or there has been dirt that has gotten inside the lock core then there is a possibility that the lock can get stuck. I recommend that you spray some…

view full answer...

Answer 5

I went out to our warehouse and took some measurements for you. The #P313 Replacement Receiver Insert measures 1.31 in x 0.87 in while #P333 measures a bit smaller at 1.30 in x 0.75 in. See the attached images. #P313 is designed to replace the…

view full answer...

Answer 6

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bikes racks with 2 inch shanks. This hitch pin has an outer diameter of 5/8 inch. If your bike rack has a 1-1/4 inch shank then you will want to use #P5902. This…

view full answer...

Answer 7

I would be happy to help! I had our warehouse measure the Draw-Tite Trailer Hitch Receiver #76116 you were looking at and it measures 4-7/8" from the center of the hitch pin hole to the back of the receiver as shown in the included diagram. For…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...