Will The Threaded Hitch Pin # P5901 Fit a Swagman RV Bike Rack With 2" Shank?

Question

Question:

Hi, I have the Swagman RV approved bike rack hitch. Number SR-8190-02. Will the 5901 hitch bolt work with the above? It has a 2 shank. Thanks

asked by: Bob S

0

Expert Reply:

I want to make sure I get you the correct information but I cannot find any information on a Swagman SR-8190-02 bike rack. The Threaded Hitch Pin and Clip # P5901 is proprietary size used on Swagman bike racks with a threaded 2" hollow tube shank. It is not compatible with units having a 1-1/4" shank with 2" adapter.

expert reply by: Bud M

0

Answer 1

I believe you are looking for a replacement hitch pin bolt for a Swagman bike rack. For that we have the part #P5901 for just the pin/bolt or if you wanted to upgrade to a locking hitch pin we have the #S64029.

view full answer...

Answer 2

The Swagman Traveler XC2 Bike Rack for 2 Bikes - 2" Hitches or RV Bumpers #S64663 is designed to work with the 2" receiver on your truck as well as the included RV bumper mount receiver so you should have no problems using the threaded…

view full answer...

Answer 3

I went out to our warehouse and took some measurements for you. The #P313 Replacement Receiver Insert measures 1.31 in x 0.87 in while #P333 measures a bit smaller at 1.30 in x 0.75 in. See the attached images. #P313 is designed to replace the…

view full answer...

Answer 4

If you leave the hitch lock for the Swagman Dispatch 2 Bike Platform Rack part #S44FR on for too long or there has been dirt that has gotten inside the lock core then there is a possibility that the lock can get stuck. I recommend that you spray some…

view full answer...

Answer 5

The usable length of the Replacement Threaded Hitch Pin and Clip #P5901 is roughly 3-1/4". I recommend measuring this on your 2-1/2" receiver to verify fitment as not all receivers will have the same dimensions. We do have the longer…

view full answer...

Answer 6

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bikes racks with 2 inch shanks. This hitch pin has an outer diameter of 5/8 inch. If your bike rack has a 1-1/4 inch shank then you will want to use #P5902. This…

view full answer...

Answer 7

I would be happy to help! I had our warehouse measure the Draw-Tite Trailer Hitch Receiver #76116 you were looking at and it measures 4-7/8" from the center of the hitch pin hole to the back of the receiver as shown in the included diagram. For…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Will The Threaded Hitch Pin # P5901 Fit a Swagman RV Bike Rack With 2" Shank?

Product Page this Question was Asked From

Continue Researching