What Are the Dimensions of the Mounting Hole of the Wiring Harness for the Curt C56000

Question

Question:

What are the distance between the mounting holes? I have an existing hole in my bed and I want to get a plug that fits.

asked by: Scott

0

Expert Reply:

The dimensions of the mounting bracket that comes in the Curt 5th Wheel/Gooseneck Custom Wiring Harness # C56000 are:

Top to bottom 1-7/8 inches
Side to side 2-1/2 inches

I have attached a picture to illustrate this for you.

expert reply by: Jon G

0

click to enlarge

Answer 1

The Curt 5th Wheel and Gooseneck Wiring Harness, #C56000, will work with the 2011 Ford F-350 diesel. When our installers install this wiring harness in a truck bed, they use a 2 inch hole saw.

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 9

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

What Are the Dimensions of the Mounting Hole of the Wiring Harness for the Curt C56000

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching