Can a Weld-On A-Frame Trailer Coupler be Bolted On Instead of Welded

Question

Question:

can i buy an a-frame bolt on trailer coupler.........can i bolt on a weld on a-frame coupler

asked by: Mark

0

Expert Reply:

The A-frame couplers we carry, like # 12660-97SP, are weld-on applications and cannot be bolted on to a trailer frame. Any welding should be done by a qualified welder in a shop that works on trailers. The coupler you have reference accepts a 2-5/16 inch diameter ball. I have included a link to all of the A-frame coupler options for you to view.

expert reply by: Michael H

0

Answer 1

I more or less agree with you. The Fulton Fold-Away Hinge Kit for 3 x 3 inch Trailer Tongue - Weld-On, item # FHDPW330300, is a cleaner look and if you got a bad weld job you would not have a safe setup. I have done some welding, I am in no way a…

view full answer...

Answer 2

Dexter Trailer Axle #T20BTR-EZ-7258 has a shipping weight 22-lbs. Its actual rated weight-carrying capacity is 2200-lbs. It could be used with leaf springs such as #e84SR, a pair of which is rated for 2000-lbs.

view full answer...

Answer 3

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's manufacturer that…

view full answer...

Answer 4

The Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2-5/16" Ball - 21K #12660-97SP does not have any bolt information, with the reason being that this is a weld-on application and cannot be bolted on. I did cut out the…

view full answer...

Answer 5

You'll need to use a circuit tester like #PTW2992 and test each pin on your 7-way as its function is activated. The pin in the 3:00 position should light up when the right turn signal and when the brake pedal is activated. The pin in the 9:00…

view full answer...

Answer 6

First, use a circuit tester like #40376 if needed, to test the 7-Way trailer connector. The 12-volt circuit will be in the 1 oclock position. If the trailer side connector pin that corresponds with the 12-volt circuit is connected to the battery on…

view full answer...

Answer 7

The importance of matching a wheel's pilot hole diameter to the part of the hub that fits through it depends on the type of wheel. A hub-centric wheel uses the pilot hole to center the wheel on the hub and also to bear some of the total weight…

view full answer...

Answer 8

You were given some correct information. The new trailer wheels you purchased that have a larger pilot hole will still be compatible with your hubs in terms of being properly centered. The key is indeed the coned lug bolts, such as #RG02-020. These…

view full answer...

Answer 9

If you are changing the wheels from 8 inch to 12 inch and have a 4 on 4 bolt pattern, and If the wheel is stud-piloted, then the pilot hole hole does not matter. However, if the wheel is centered using the pilot hole, then you will need to find a…

view full answer...

Answer 10

There are two different types of trailer hubs that will determine if the pilot hole on a wheel matters or not. First there are hubs that use wheel bolts to secure the wheel to the hub. These are called hub-centric. For this type, the pilot hole has…

view full answer...

Answer 11

As long as your wheels are not "hub-centric" and use conical-styled lug nuts your wheel will be centered by the lug nuts and still be compatible even though the pilot hole of the #AM34834 is bit larger than you need. Because the pilot hole…

view full answer...

Answer 12

If the pilot hole on the wheel was larger than 4-3/4 inches, and the wheel is center on the hub using the lug nut rather than wheel bolts, it would not matter. But since the wheel pilot hole is smaller, you will not be able to use the hubs you…

view full answer...

Can a Weld-On A-Frame Trailer Coupler be Bolted On Instead of Welded

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching