Recommended Dust Cover Plugs For Dexter Brake Assemblies

Question

Question:

Hi, I purchased a set of dexter e brakes 23-464 and 23-465. Do you carry a dust cap for adjustment opening? Thanks

asked by: Nirbhai B

0

Expert Reply:

The dust caps for the adjustment opening on your Dexter brake assemblies I recommend are the Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4 # BP10-220. These will work great with your assemblies.

expert reply by: Jason S

0

Answer 1

According to TST, once the repeater is installed, the sensors included with the #TST-507-INT-6-C will work within 5 minutes. My representative tells me that the expected battery life is 3-5 years, and once the battery goes dead, the sensor itself…

view full answer...

Answer 2

I walked out to our warehouse and pulled the Redline Adjuster Plugs #BP10-220, from our inventory. Checkout the short video I shot for you which shows the dimensions of the plug.

view full answer...

Answer 3

The Dexter Electric Trailer Brake Kit #23-26-27 contains both the left and right hand brake assemblies that replace your 36-19 assemblies on your 2017 Keystone Passport. Yes, you can replace them with the Dexter Nev-R-Adjust Electric Trailer Brake…

view full answer...

Answer 4

For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…

view full answer...

Answer 5

Yes, to replace the adjuster plugs on Dexter Electric Brake Assemblies like the 10" #K23-463-00 that you were looking at you just need the part #BP10-220. These plugs can be used on all of the common electric brake sizes (7 inch, 10 inch, and 12…

view full answer...

Answer 6

The 2-1/2" Lubed Dust Cap and Rubber Plug #DC250L-DCRP is the size most commonly found on the 5,200lb Dexter Axles. The cap is has a 2.45" outside diameter where it slides into the axle hub. You can confirm that this is the correct…

view full answer...

Answer 7

Yes we have the replacement brake assembly plugs with part #BP10-220.

view full answer...

Answer 8

If your current brake assemblies are self-adjusting, once the hub/drum is removed you will be able to see the adjuster cable extending across the brake assembly as shown in the photo I have edited for you. If you find you do not have them, you can…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 11

Bill yes, the Brass Tire Sensors for TST TPMS #TST-507-RV-S2 will work great with your TST TPMS for RVs - Color Display - Signal Booster #TST-507-RV-4-C. These sensors were designed specifically to be used with that system as well as the 6 sensor…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...