Does Timbren Axle Less System A20RS545 have Rim Diameter Restrictions

Question

Question:

Are these included hubs have any wheel size restrictions similar to dexters that are sized from 8-12inch or 13-15?

asked by: Erik

0

Expert Reply:

The hub that comes with the Timbren part # A20RS545 that you referenced is the part # TA88545-2 which does not have the same rim diameter restriction as other hubs do.

expert reply by: Jameson C

0

Answer 1

Looks like you found the chart that Jeff D made that shows common axle capacities based on diameter: Typical Axle Diameters Based on Axle Capacity - 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter - 3,500-lb Axles: 2-3/8 inch diameter -…

view full answer...

Answer 2

The correct spindle nut to use with the spindle part #TRU27FR is the part #165686.

view full answer...

Answer 3

The spindle part #TRU27FR would require a hub designed to fit BTR spindles like the part #AKIHUB-545-2-2K. Then you could use up to a 12 inch diameter wheel and tire combo with a 5 on 4-1/2 inch bolt pattern like the Kenda 5.30-12 Bias Trailer Tire…

view full answer...

Answer 4

Yes, the 2 Trailer Idler Hub Assemblies #TA88545-2 will fit on 2 of the BTR E-Z Lube Spindles #TRU27FR. The hubs include the correct Bearings #L44649, Races #L44610, Seals #RG06-020 and Grease Caps #RG04-040 for the spindle.

view full answer...

Answer 5

The Lippert Lubed Straight Spindle with Brake Flange #TRU27FR has a stub diameter of 1-5/16" and is designed to fit a 2,500-lb axle. If your tow dolly has those specifications, this spindle will work on your axle. If you're not sure, check…

view full answer...

Answer 6

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 7

There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over…

view full answer...

Answer 8

It looks like you might be asking about a few different torque specs so I'll address all of them separately. For a trailer axle spindle nut like part #165686 you will need to run the spindle nut down until there is no more side-to-side play in…

view full answer...

Answer 9

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 10

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist.…

view full answer...

Answer 11

According to our installers you will tighten the trailer spindle nut until it stops by itself. In other words do not torque it down as hard as you can. It just has to be tight. A little play is to be expected. You do not want to torque it down too…

view full answer...

Answer 12

There is not a torque spec on the axle nut for the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 #84545BX. The axle will have a castle nut that should be tightened until there is no side to side play and then backed off to the…

view full answer...