How Tight Should Castle Nut be on Trailer Hub
Question:
2005 Horton car hauler with 6000 lb. Dexter EZ lube axles. I bought this used and noticed that all 4 wheels had play in them, so when I repacked the bearings I tightened the nut enough to eliminate the play but still allow the wheel to turn freely. Using a laser thermometer, I took it out for about a 20 minute drive loaded with a car in the trailer. I noticed the hubs came up to 95-115 degrees within about 2 miles, but never got any hotter than that. The air temperature was 55 degrees, so about a 40-50 degree temp rise. Is that normal or do I have the bearings too tight?
asked by: Robert B
Expert Reply:
There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over tightening the nut can lead to the spindles and bearings overheating, which can damage them.
We have a video that outlines the proper way to remove and install a trailer hub, to view the video, click on the provided link.
95 degrees on a 55 degree day seems a bit warm. I would try the above mentioned install method for the nut which should reduce the tension.
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Proper Way to Tighten Trailer Spindle of Castle Nut
- Video: Remove and Reinstall a Trailer Hub Review
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Article: Most Popular Wheel Bearings
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: How Tight Should Spindle Castle Nuts be Tightened
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7K
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Trailer Wiring
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Video: Bearing Repacking and Grease Seals Installation
- Q&A: When Do Brakes Need to be Added to Both Axles of Tandem Axle Trailer
- Q&A: Enclosed Trailer Side Door Frame and Trim
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Q&A: How Thick Are Electric Brake Shoe Pads and When Should They be Replaced
- Article: Trailer Wiring Diagrams
- Search Results: dexter wheel bearings
- Search Results: wheel bearings
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Shop: Transmission Cooler
- Video: Derale Transmission Coolers - Plate-Fin Cooler - D13614 Review
- Video: Derale Series 9000 Plate-Fin Transmission Cooler Kit Review
- Q&A: Installation Video for Derale Transmission Cooler D13504
- Article: How to Bleed Your Trailer Surge Brakes
- Shop: Front Mount Hitch
- Search Results: hubs
- Shop: Brake Controller
on Trailer Bearings Races Seals Caps
