Curt Q25 Leg Kit to Fit Above the Bed Rails in Truck Bed

Question

Question:

I see that thee go from rail mount to factory pucks. I have a Q25 with these legs and need to go the other way- from puck back to rail mount. Assume that is possible- what would part be Thank you

asked by: Obie A

0

Expert Reply:

We have just what you need. The leg kit you need is the Curt Q25 leg kit part # C16963 which will allow your to install your Curt Q25 head in factory above the bed rails.

expert reply by: Jameson C

0

Answer 1

The Curt A25 #C16046 and Q25 #C16049 are both excellent 5th wheel hitches however there are a few upgrades on the newer Curt A25 #C16049 that make it the superior hitch and my personal recommendation. The primary difference between the two models is…

view full answer...

Answer 2

We do have the replacement 5th wheel hitch legs for your Head Unit for Curt Q24 5th Wheel Trailer Hitch #C16545. - Curt OEM 5th Wheel Hitch Legs for Chevy/GMC Towing Prep Package #CU53FR. The Curt OEM 5th Wheel Hitch Legs for Chevy/GMC Towing Prep…

view full answer...

Answer 3

Both the Curt A25 #C24FR and the B&W Companion #BWRVK3715 have a 25,000 pounds towing and 6,250 pounds of vertical load capacity, but there are a few differences between them and I have a couple listed below. First, The B&W can be adjusted…

view full answer...

Answer 4

The Replacement Base Legs for Curt Q5 and Q24 5th Wheel Hitches #16125-SK13 and the Replacement Base Legs for Curt Q25 5th Wheel Trailer Hitch #C16963 are slightly different. My contact at Curt said the bolt pattern in the same, so you can put either…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 10

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 11

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 12

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Curt Q25 Leg Kit to Fit Above the Bed Rails in Truck Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching