Wiring Diagram for the Curt 4 Pole to 7 Pole Adapter # C57674 And Wiring for Trailer Brakes
Question:
Please provide wiring diagram for C57674, the link showing the wiring directions on your web site does not work. I do not have a Brake controller, this will be used on a small trailer with a battery pack and brakeaway brakes. I am not sure how to wire the blue and black wire. I realize the white is ground and I plug a flat 4 pin into this item. Thank you.
asked by: Gary L
Expert Reply:
The wiring for the Adapter 4 Pole to 7 Pole and 4 Pole, item # C57674, is wired as follows. The white wire is grounded to the vehicle frame as you have indicated. The Yellow wire is the center pole of the 7-Way connector and is normally used for connection to the reverse light circuit. In your case you will not need the yellow wire.
The blue wire is for connection of the electric brake feed wire from a brake controller. You will need a brake controller in your Sienna to activate the trailer brakes on your trailer when towing. Once the brake controller is installed in the vehicle you will need to connect the mating connection in the 7-Way on your trailer to the trailer brakes power lead.
The black wire is the 12 volt power wire and will need to be ran to the positive terminal of the vehicle battery through a 40 amp circuit breaker, item # PK54540. this wire will be used to maintain the charge of a trailer mounted accessory battery and/or a breakaway battery.
Once you have the 7-Way connector installed you will need to wire a brake controller in your Sienna. I would recommend the Prodigy P2 Brake Controller, item # 90885, for easy setup and use. Wiring the brake controller will require extra wiring and finding the stop light switch behind the brake pedal on your vehicle. A circuit tester, item # PTW2993 will be needed to locate this wire. We have a kit, item # ETBC7, that includes all of the wiring, circuit breakers, hardware, and a connector just like the C57674 connector that you referenced.
I have included links to instructions for wiring a brake controller and the connector on your vehicle. I also included a diagram, see photo at right, for wiring a breakaway battery, item # 20099 on your trailer, if you need to complete that installation. Using a breakaway battery only for the trailer brakes will not give you control of the trailer brakes when towing, they will only be applied in the event of an accident where the trailer is disconnected from the vehicle. Having the Trailer brakes operative may well help avoid such an incident.
Products Referenced in This Question
Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- Hopkins
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Adapter 4 Pole to 7 Pole and 4 Pole w/Test Lamps
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Roadmaster Single Park Light Diode
- Shop: Adapter 4-Pole to 7-Pole and 4-Pole
- Shop: Adapter 4 Pole to 7 Pole and 4 Pole w/Test Lamps
- Q&A: Gauge of Black Wire for Curt 4-Way to 7-Way C57674
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: Troubleshooting Pre-Collision Warning After Installing Brake Controller on 2019 Toyota Highlander
- Q&A: Diode for Installation of Brake Controller on 2018 Toyota Highlander
- Article: Trailer Wiring Diagrams
- Search Results: 10 gauge duplex wire
- Shop: Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Video: Deka Wiring 10-2-1 Review
- Video: Curt Wiring - Wiring Adapters - C57674 Review
- Video: Curt 4 Pole to 7 Pole and 4 Pole Adapter Review
- Search Results: gen x
- Search Results: 2 inch ball 1.25 shank
- Article: Trailer Hitch Receiver Sizes
- Q&A: Where Does the Cable for the Break Away Switch Attach on the Tow Vehicle
- Q&A: Can a Ball Mount Be Inverted To Give a Rise Instead of Drop
- Q&A: Recommended 2 Inch Hitch Ball with 1.25 Inch Diameter Shank
- Shop: Trailer Hitch
- Shop: 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Search Results: trailer lowering kit
- Search Results: 7 way tester
- Article: Tips on How To Tow a Trailer
- Shop: Towing Mirrors
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring