Replacement Wheel Bolt and Stud For Keystone Sprinter 5th Wheel

Question

Question:

Wheel Bolt and Stud for 2015 Keystone Sprinter 5th wheel

asked by: Paul B

0

Expert Reply:

You will need to check the diameter and length of the wheel bolt you are looking to replace. We do have replacement options for your hubs whether they are 1/2 inch diameter like # K12WB169, 9/16 inch like # K916WB25, or 5/8 inch like # K58WB316. I have linked our page so you can see all your options of wheel studs. I have also linked the pages for wheel bolts in both coarse and fine thread.

We also have lug nuts for all these bolt/stud options.

expert reply by: Jason S

0

Answer 1

The Kodiak Wheel Bolt - 9/16" Diameter x 2-1/2" Long #K916WB25 can replace your 5/8 studs as long as the knurl diameter and length work for your hub and wheel. For instance, the Kodiak Wheel Bolt - 5/8" Diameter x…

view full answer...

Answer 2

It looks like you recently purchased some Kodiak Wheel Bolts #K58WB316 and 5/8" flange nuts #95188 from us, so thank you for being a loyal customer! What you'll want to torque those to will depend on the construction of your wheels…

view full answer...

Answer 3

The standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part #7-122 which is the correct thread size and length.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Replacement Wheel Bolt and Stud For Keystone Sprinter 5th Wheel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching