Will Tow Ready Vehicle Wiring Harness 118491 Fit a 2011 Honda Pilot EX-L

Question

Question:

Will this harness work for Pilot 2011 EX-L ?

asked by: Andrey S

0

Expert Reply:

Yes, the # 118491 T-One connector with upgraded circuit protected ModuLite fits all models of the 2011 Honda Pilot, including those with the EX-L trim package. It should work well for your application.

You can view the installation instructions for the wiring at the link provided, as well as a video showing it being installed on a 2010 Pilot.

expert reply by: Sarah L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Yes, it is! Honda and other manufacture's like to leave the fuses out of new vehicles that do not come with a functional towing package to save on costs. You can verify if you're missing the fuses by checking your fuse box but I am pretty…

view full answer...

Answer 4

To add a hitch to your 2024 Honda Pilot, I recommend the etrailer item #e27KR. This hitch is custom fit and bolts to your Honda with included hardware. I really like the etrailer hitch item #e27KR because it installs behind your rear bumper cover and…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...