Timbren Kit that Fits 2008 Ram 3500 Cab and Chassis

Question

Question:

My 2008 RAM 3500 DRW CTD has the rear Torklift Top and Bottom Stable Loads and Rancho 9000 adjustable Shocks... I haul a 3500 truck camper... Do I need to add rear Timbrens ??? Note: I have replaced the RAMs front bump stops with Timbrens...

asked by: Jackson

0

Expert Reply:

If you are wanting further suspension support for the rear of your 2008 Ram 3500 a Timbren can be added. For that the correct part number is # TDR3500CA.

This will provide you with 8,600 lbs more of rear suspension support but does not actually give you the ability to exceed the weight capacity of your truck.

expert reply by: Jameson C

0

Answer 1

The StableLoad designed for your 2013 Dodge Ram 3500 SRW is part #TLA7311. The TorkLift StableLoads will help some with leveling the load but were designed to help stabilize it from body roll and side to side sway when hauling a heavy payload. If…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Timbren Kit that Fits 2008 Ram 3500 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching