Will 16 Inch Tires Fit Timbren Axle-Less Suspension System # ASR35HDS05

Question

Question:

I build a off-road camp trailer wich the estimate weight full charged is about 3200 lbs. The wheels wich be used are the MICHELIN 4X4 O/R XZL 750/- R16. Do you think suspensions #ASR35HDS05 are adapted ?

asked by: Alexandre

0

Expert Reply:

As long as there is a hub that fits the spindle and has the bolt pattern needed for the wheels then yes the Timbren Axle-less system # ASR35HDS05 will work with 7.50-16 tires. For example hub # AKIHUB-655-6-EZ-K will accept 16 inch tires as long as the wheel has a 6 on 5-1/2 bolt pattern. I have linked a help article on determining wheel bolt patterns for you.

expert reply by: Michael H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 6

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Answer 7

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 8

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The Dexter Trailer Hub Assembly you referenced, part #AKIHUB-440-2-1K is known as an idler hub. An idler is a hub that is no provisions for trailer brakes. It has no brake drum. Part #8-276-5 is an example of a hub/ drum that has a brake drum that…

view full answer...