Idler Hub that Fits Timbren Axle Less kit part # ASR2000S02

Question

Question:

Can I use idler hubs on this particular Timbren Axle less part. I dont feel that I will need to have brakes at this time, but I want the option to add them at a later date if I choose. What idler hub with bearings are compatible this this product?

asked by: Larry

0

Expert Reply:

For an idler hub that fits the Timbren kit part # ASR2000S02 you would want the part # 8-91-05UC1-EZ which comes with the needed bearings.

expert reply by: Jameson C

0

Answer 1

For a hub with a 5 on 4-1/2 inch bolt patter that fits the Timbren Axle Less Kit part #ASR2000S02 we have the part #AKIHUB-545-35-EZ-K. These come pre greased to save a little time and energy.

view full answer...

Answer 2

As long as you can get the spindle height of the Timbren system part #ASR2000S01 to match your other axle you should be just fine to use it with a standard style axle. The center of this spindle will end up being 2-5/8 inches below the bottom of the…

view full answer...

Answer 3

We've had this question sent into us before and when we spoke with Timbren they told us that the C-channel frame design will be fine assuming that he open part of the C is on the inboard side and not the outboard side of the frame. If the C…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...