Replacement Hardware for Stromberg Carlson Folding RV Handrail

Question

Question:

Could I buy just the mounting hardware i.e. without the handrail?

asked by: Adam Z

0

Expert Reply:

The hardware for the Stromberg Carlson Folding Handrail # AC-530 is no longer available as a kit. You would have to purchase the entire kit. If you will be drilling and mounting into a stud you will only need the correct screws which are as follows.
(6) #14 x 3” Phillips head mounting screws,
(2) #8-32 x 3/8” pan head screws for securing mounting bracket covers.

expert reply by: Jared P

0

Answer 1

The mounting brackets of the Lend-A-Hand part #AM-533 that you referenced measure 2-5/16 inches wide x 3-7/8 inches in height.

view full answer...

Answer 2

The Stromberg Carlson Lend-a-Hand Extra Large Folding Grab Handle #AM-533 does include four mounting screws for installation on an RV door stud. The handle can mount on either side of a door but it folds in only one direction (toward the rear of the…

view full answer...

Answer 3

The shim kit part #5991-SM is designed to push the handle part #AM-533 out a little further from the body of the RV so that it can close around a door that sticks out further from the outer wall. So if your door closes mostly flush with your RV wall…

view full answer...

Answer 4

The mounting bracket spacing of the Lend-a-Hand Extra Large Folding Grab Handle #AM-533 is 19-1/4 inches as opposed to 31 inches, and this handle has the closest spacing to the 17-3/4 inches you mentioned needing. If you are having a bit of trouble…

view full answer...

Answer 5

The Stromberg Carlson shim kit, part #5991-SM, is just one shim. It's kind of misleading since it's called a kit but if you need two you do need to order two of them.

view full answer...

Answer 6

I measured the brackets of the Lend-a-Hand Folding Grab Handle for RVs #AM-200 and found from the surface to the edge where the handle locks is approximately 1-5/16". Since you measured your awning support and it is 1-3/8" then you will be…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...