Does Stromberg Carlson Lend-a-Hand Folding Grab Handle AM-533 Include Hardware

Question

Question:

Does the Stromberg Carlson extended hand rail fold in either direction on the RV? Does it come with all mounting hardware needed?

asked by: Jim H

0

Expert Reply:

The Stromberg Carlson Lend-a-Hand Extra Large Folding Grab Handle # AM-533 does include four mounting screws for installation on an RV door stud. The handle can mount on either side of a door but it folds in only one direction (toward the rear of the RV when mounted on the passenger side).

expert reply by: Adam R

0

Answer 1

The mounting brackets of the Lend-A-Hand part #AM-533 that you referenced measure 2-5/16 inches wide x 3-7/8 inches in height.

view full answer...

Answer 2

The shim kit part #5991-SM is designed to push the handle part #AM-533 out a little further from the body of the RV so that it can close around a door that sticks out further from the outer wall. So if your door closes mostly flush with your RV wall…

view full answer...

Answer 3

I measured the brackets of the Lend-a-Hand Folding Grab Handle for RVs #AM-200 and found from the surface to the edge where the handle locks is approximately 1-5/16". Since you measured your awning support and it is 1-3/8" then you will be…

view full answer...

Answer 4

The mounting bracket spacing of the Lend-a-Hand Extra Large Folding Grab Handle #AM-533 is 19-1/4 inches as opposed to 31 inches, and this handle has the closest spacing to the 17-3/4 inches you mentioned needing. If you are having a bit of trouble…

view full answer...

Answer 5

The hardware for the Stromberg Carlson Folding Handrail #AC-530 is no longer available as a kit. You would have to purchase the entire kit. If you will be drilling and mounting into a stud you will only need the correct screws which are as follows.…

view full answer...

Answer 6

The Stromberg Carlson shim kit, part #5991-SM, is just one shim. It's kind of misleading since it's called a kit but if you need two you do need to order two of them.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Does Stromberg Carlson Lend-a-Hand Folding Grab Handle AM-533 Include Hardware

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching