Measurements of etrailer Single Axle Trailer Fender

Question

Question:

Need width and length measurements or the part # the above mentioned will tell me F13x361R

asked by: Robert G

1

Helpful Expert Reply:

The etrailer Single Axle Trailer Fender # HP66VR measures 13 inches wide x 36 inches long x 20 inches tall. It's made of 16-gauge steel to fit single axle trailers with 16 to 16-1/2 inch wheels.

expert reply by: Charles S

1

Answer 1

The dimensions are below for the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1500. Overall dimensions of the plate- 6” X 8” Bottom of the plate to the bottom of the socket Fin (brace) – 2-1/4" Bottom of the plate to the end of…

view full answer...

Answer 2

You will wire a load resistor into the wiring of each light socket that has an LED bulb and flashes. So basically you will need to wire a load resistor into any bulb that blinks or has a dual intensity feature that lights up when the brakes,…

view full answer...

Answer 3

You will wire a load resistor into the wiring of each light socket that has an LED bulb and flashes. So basically you will need to wire a load resistor into any bulb that blinks or has a dual intensity feature that lights up when the brakes,…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The Triple-Axle Trailer Hanger Kit #APTT3 that you referenced is designed to work on axles with capacities of 2,000 lbs to 7,000 lbs so it should work very well for you. I attached a picture that has a chart that shows exactly how you should space…

view full answer...

Answer 7

In order to calculate where the axles would go on your trailer, there are several things that need to be taken into consideration. You will have to mock up the trailer with the suspension and axles to get the weights needed to determine where the…

view full answer...

Answer 8

In the image with the suspension setup the equalizer #TREQ105 is placed between the front and second axles. Just like you have on your trailer. The front of the equalizer connects to the spring using a shackle strap and the rear is connected directly…

view full answer...

Answer 9

Different trailer configurations require different equalizers. It all depends on the springs, axle spacing, hanger spacing, height needed and so on. In many cases if you want to change the equalizer to something with different measurements you would…

view full answer...

Answer 10

Equalizers for trailer suspension have different shapes, lengths, and heights to accommodate different axle spacing, spring lengths, and deck heights. Going to an equalizer that is not the same length and height as the original will require replacing…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Measurements of etrailer Single Axle Trailer Fender

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching