Replacement Landing Gear Legs for 2010 Cougar 320SRX

Question

Question:

I AM LOOKING FOR YOUR PART NUMBER FOR THE FRONT POWER JACKS ON MY 2010 COUGAR 320SRX FIFTH WHEEL. I NEED THE RIGHT AND LEFT JACKS.

asked by: WAYNE K

0

Expert Reply:

From previous customers with your trailer we have determined that your trailer has Lippert landing gear. For replacement follow leg you would want part # LG-179014 and then for the lead leg part # LG-179013.

expert reply by: Jameson C

0

Troy M.

5/23/2020

Replacement Landing Gear Legs for 2010 Cougar 278rks. Looking for the part numbers as well for the left and right power jacks 2010 Cougar 278rks.

Reply

Chris R.

5/26/2020

Unfortunately I wasn't able to track down information on the original landing gear system for your 2010 Cougar 278RKS. Is there by chance an information sticker located anywhere on the legs? If not, can you tell me the spacing between the two mounting brackets on one of the legs?

Helpful Links

dept-pg-accessories_and_parts-pt-legs.aspx

Reply

Answer 1

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 2

The Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs #LG-1 is a complete landing gear and motor set that's a popular replacement we've seen used on many Keystone Cougar 5th wheel trailers, but you'll…

view full answer...

Answer 3

I believe you are referring to the Lippert Components High-Speed Power Stabilizer Jack part #LC369774 that comes with the white switch part #LC144214. Lippert was not able to provide me a wiring diagram for the white switch but was able to give me…

view full answer...

Answer 4

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Replacement Landing Gear Legs for 2010 Cougar 320SRX

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching