Available Sizes of Heat Shrink Tubing

Question

Question:

DW05451 Is the item one piece of 6 foot heat shrinkable tubing?

asked by: Kturgeon@namtek.com

0

Expert Reply:

Part # DW05451 is a pack of 25 six-inch lengths of heat-shrink tubing. This tubing fits wire from 14-gauge to 18-gauge. Similar item # DW05449 works on wires from 10- to 14-gauge. You can use a heat gun like # ALL836717 to shrink the tubing once your electrical connections are complete.

expert reply by: Adam R

0

Answer 1

You could use the Trailer Wiring Junction Box #38656 on a trailer with 4-way wiring. You would just have a few extra pins available on the box that you wouldn't end up using.

view full answer...

Answer 2

In order to join lights together on a boat trailer you'll want to use heat shrink butt connectors like part #DW05743-10, part #DW05744-10, and part #DW05745-10 as they keep out moisture which reduces the chance for corrosion that cause…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Available Sizes of Heat Shrink Tubing

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching