Can the Trailer Wiring Junction Box # 38656 be Used with a 4-Way

Question

Question:

Description states for for either 6- or 7-way connectors. I assume can be used with 4 way connector as well. Can you confirm?

asked by: Ed

0

Expert Reply:

You could use the Trailer Wiring Junction Box # 38656 on a trailer with 4-way wiring. You would just have a few extra pins available on the box that you wouldn't end up using.

expert reply by: Jameson C

0

Answer 1

In order to join lights together on a boat trailer you'll want to use heat shrink butt connectors like part #DW05743-10, part #DW05744-10, and part #DW05745-10 as they keep out moisture which reduces the chance for corrosion that cause lighting…

view full answer...

Answer 2

Part #DW05451 is a pack of 25 six-inch lengths of heat-shrink tubing. This tubing fits wire from 14-gauge to 18-gauge. Similar item #DW05449 works on wires from 10- to 14-gauge. You can use a heat gun like #ALL836717 to shrink the tubing once your…

view full answer...

Answer 3

The junction box #38656 is for exactly what you're trying to do. It makes the wiring look a lot cleaner and keeps the connections out of the way. You also need some ring terminals to make the connections. I've linked our selection so you can…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Can the Trailer Wiring Junction Box # 38656 be Used with a 4-Way

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching