Will Lippert Replacement Lead Landing Gear Leg Fit a 2010 Heartland Sundance 3200es

Question

Question:

Was wondering if this replacement will work on 2010 Heartland Sundance 3200es

asked by: Devin J

0

Expert Reply:

Replacement landing gear jack leg # LC179013 will most likely fit your 2010 Heartland Sundance trailer. Many of the jack manufacturers make landing gear jacks that are interchangeable with each other so you would need to look at the bracket stop measurements on your existing jacks.

The standard measurement used by most jacks is 17-1/2 inches from the top of the upper bracket stop to the bottom of the lower bracket stop as shown in the picture I have included.

The other thing to consider is the outer tube overall height (not the overall height of the whole jack, just the outer tube). On this replacement lead leg the outer tube is 29-1/2 inches tall.

expert reply by: Michael H

0

click to enlarge

Answer 1

Your fifth wheel rails with the CMI stamped on them were manufactured by Curt, and will be compatible with Curt, Draw-Tite, Husky, Reese, Valley, and other brand hitches. They fit what are called industry standard hitches. For your 2008 Ford F-350,…

view full answer...

Answer 2

Essentially the #LG-196308 and the #LC196308 are identical. I'd go with the lower priced of the two since neither is a better choice than the other.

view full answer...

Answer 3

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 4

If the landing gear on your brand new Forest River Trailer is not working at all, either to extend or retract the legs, then most likely there is some kind of a power issue. I do recommend starting by making sure the battery is charged and in good…

view full answer...

Answer 5

Yes, if the support arms on your LCI Power Stabilizer Jack Model 1917771 are black then you will need the Replacement Electric RV Stabilizer Jack Motor part #LC138445 but if they are yellow then you will need the Replacement Electric RV Stabilizer…

view full answer...

Answer 6

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 7

We do carry some Lippert Hydraulic jacks but none by those part numbers. I tried looking them up on Lipperts site and found nothing on the 2571254 number and the 25712510 seems to have been superseded by a jack with a 14,000 lb. capacity, but not one…

view full answer...

Answer 8

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 9

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 10

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 11

I don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately. The Replacement Crank Handle…

view full answer...

Answer 12

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Will Lippert Replacement Lead Landing Gear Leg Fit a 2010 Heartland Sundance 3200es

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching