Snatch Block/Pulley Block for Use with a 5,000 Pound Boat and Electric Winch

Question

Question:

Will this work with an electric winch for pulling a boat onto a trailer on a boat ramp? The boat is 5000 lbs.?

asked by: Paul P

0

Expert Reply:

You can use pulley block # BDW20004 for your winching needs but it is rated at 4,000 pounds so if at any time the full weight of the boat is on the block it would exceed the capacity. For a higher capacity option I recommend # CU881081 which is rated for 6,000 pounds

expert reply by: Michael H

0

Answer 1

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 2

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 8

The wiring kit you are going to need to go with is one that has a thick enough gauge to provide the amperage requirements of your winch and also has a long enough length to make it from your battery to the rear of the vehicle. Since I looked up the…

view full answer...

Answer 9

Since your Harley isn't one of the standard fits that they have a B and W Biker Bar designed for you would need to use the Custom Frame version part #BWMC2304 which can fit basically any Harley Davidson frame available due to how adjustable it…

view full answer...

Answer 10

You will need to pull down on the release handles of the B&W Biker Bar Motorcycle Tie-Down System #BWMC2304 which will allow the bike to be released from the mount and then you will be able to push the bike forward. See attached picture to see…

view full answer...

Answer 11

For your 2018 Harley Davidson CVO Street Glide you will actually want to go with the B&W Biker Bar Motorcycle Tie-Down System #BWMC2301 which will work perfectly with your motorcycle. I included a few videos of the B&W Biker Bar #BWMC2301 for…

view full answer...

Answer 12

You can use a pulley block like part #BDW20005, to pull your car on to a trailer with the winch being offset. You will want to make sure the winch is well secured for safety. This pulley block has a capacity of 17,000 lbs break strength and is…

view full answer...

Snatch Block/Pulley Block for Use with a 5,000 Pound Boat and Electric Winch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching