Longer 2 inch Hitch Ball Mount Recommendation that Has 4 inches of Drop

Question

Question:

I am looking for a 2 inch ball mount extra long with a 4 inch drop do you see those?

asked by: MIKE

1

Helpful Expert Reply:

The Curt ball mount part # C45270 fits a 2 inch hitch, has 4 inches of drop and is longer at 13 inches from the center of the hitch pin hole to the center of the ball hole.

expert reply by: Jameson C

1

Answer 1

I certainly can, I went out into our warehouse and grabbed a Curt Ball Mount part #C45270 to grab the dimension you asked for plus a few extras just in case.

view full answer...

Answer 2

The Curt Class III Drawbar #C45270 is made in the USA. It has a 4" drop and a 2" rise with a weight capacity of 7,500 lbs.. The Convert-A-Ball Interchangeable Ball Set #900b is also made in the USA. This will allow you to quickly change…

view full answer...

Answer 3

I have a solution for you, but the Roadmaster Anti-Rattle Hitch Extender for Tow Bars - 2" Hitches - 7-3/4" Extension, #RM-071-1075, is designed to be used in flat towing applications. When flat towing a vehicle behind an motorhome there is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Longer 2 inch Hitch Ball Mount Recommendation that Has 4 inches of Drop

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching