What Hub Would Fit Spindle that Has Dimensions of 1 inch and Tapers to 1.25 inches
Question:
I cannot seem to determine if this is a straight spindle or tapered. I put a caliper on the initial part of the spindle it and it is 1 inch. However, theres a piece towards start of the spindle towards the inside of the wheel that is larger in diameter. Does this make this tapered? I measured this to be 1 1/4. I cannot seem to find any wheel hubs that are 1 and 1 1/4 tapered. Im wondering if the larger part is part of the old wheel bearing? I pulled on it but its on solid. I enclosed a picture, let me know if you need a different angle. The trailer is pretty small 4x6. Let me know if you have any thoughts on this. Thanks!
asked by: Wesley B
Expert Reply:
Most likely you have a BT8 spindle as that spindle has a .99 inch diameter where the bearings ride and then 1.25 inch where the seal rides. Can you see where the bearings ride and where the seal rides?
Dexter Trailer Hub Assembly, # 8-91-05UC1 is compatible with BT8 spindles like what you most likely have.
Products Referenced in This Question
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Hub
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Video: Review of InfiniteRule Trailer Coupler Locks - Stainless Steel Latch Lock - IR66FR
- Video: Ark Ezi-Guides Self-Aligning Boat Trailer Loading System Review
- Shop: InfiniteRule Lock for Demco eZ-Latch Trailer Couplers - 2" and 2-5/16"
- Video: CE Smith Trailer Hub Assembly Review and Installation
- Video: Review of CE Smith Trailer Hubs and Drums - Idler Hub - CE13515
- Video: CE Smith Trailer Hubs and Drums - Hub - CE13511 Review
- Video: Review of Demco Straight Tongue Trailer Coupler - Standard Coupler - DM15945
- Video: Optronics Trailer Lights - Tail Lights - TLL56RK Review
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Ark Ezi-Guides Self-Aligning Boat Trailer Loading System - 16' to 20' Long Power Boat
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: CE Smith Trailer Hub Assembly w/ Carrying Case for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Demco Channel Tongue Trailer Coupler - eZ-Latch - Zinc - 2" Ball - Bolt On - 7,000 lbs
- Shop: LED Combination Trailer Tail Lights - Submersible - Driver and Passenger Side - 25' Wire Harness
- Shop: Trailer Hitch
- Search Results: surge brake actuator
- Article: Trailer Wiring Diagrams
- Article: Trailer Tire Sizing
- Shop: Trailer Wiring
- Search Results: trailer jack
- Q&A: Replacement Drum Brake Actuator for a 1995 4 Winns Model 3916 Trailer
- Q&A: Can Electric Brakes be Used on a Boat Trailer
- Article: How to Bleed Your Trailer Surge Brakes
- Search Results: safety chains
- Shop: Brake Controller
- Search Results: l44649
- Article: Most Popular Wheel Bearings
- Shop: Suspension Enhancement
- Q&A: Which Gen-Y Gooseneck Adapter Fits 2020 Keystone Raptor 424
- Shop: Gooseneck Hitch
on Trailer Bearings Races Seals Caps
