Does Exhaust have to be Lowered to Install Curt Trailer Hitch on a 2012 Toyota Venza All-Wheel Drive
Question:
So I watched your videos for the installation. The first is for a 2WD and the video shows disconnecting the exhaust. The second one is for a AWD and shows disconnecting the stabilizer supports but does not show disconnecting the exhaust. On a 2012 AWD Venza, will I have to disconnect both the stabilizer supports and the exhaust or only the stabilizers supports? Can you confirm?
asked by: Shawn
Expert Reply:
According to the instructions for Curt hitch # 13356, linked for reference, lowering of the exhaust is required on all models. And on AWD models you also have to disconnect the sway bar brackets like you said. It might be possible to angle the hitch in without lowering the exhaust but it would be difficult.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And for trailer wiring you can use # 118482 to add a 4-Way flat connector to the rear of the vehicle. I have included a link to a video showing an example installation for you.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56079 Review
- Q&A: Installation Process for 4-Pole Trailer Wiring Harness 118482 in 2009 Toyota Venza
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Search Results: trailer hitch wiring
- Article: My Trailer Hitch Doesn't Fit
- Video: etrailer Class III Trailer Hitch Installation - 2024 Subaru Crosstrek
- Search Results: wiring harness
- Shop: Roof Rack
- Q&A: What Hitch Do You Recommend for a 2024 Toyota RAV4?
- Article: How to Measure for Trailer Hitch Drop
- Search Results: brake controller
on Trailer Hitch
